PV Logic 120w Flexi Solar Panel
120w PV Logic Flexi Panel
The 120w PV Logic flexi solar panel is most often used in motorhomes and boats for higher power demand appliances. This might be DC refrigeration, AC loads such as microwaves or for high power industrial uses such as CCTV, monitoring and data logging. Benefitting from a two year product guarantee, the panel delivers up to 780wh per day. It is supplied with a 4m cable, terminals, fuse and detailed installation instructions. NOTE – A charge controller will be needed to protect a battery from reverse feed and overcharging .
PV Logic flexi solar panels are the ultimate choice for flat or slightly curved surfaces.
Benefit from the semi-flexible panel's self-healing top surface
The ETFE top layer gives the PV Logic flexi extra resilience in really tough conditions. ETFE has a memory effect or self-healing capacity in the event the panel comes into contact with branches etc, thus ensuring any slight abrasions are ‘healed’ within a few hours. The flexi range can even be walked on with soft deck shoes! During production the ETFE is dimpled to further protect the panel and provide an anti-slip surface, particularly useful if the panel is fitted to a boat deck.
Each panel is assembled to ensure complete encapsulation. This ensures the six layer heavy duty laminate protects the solar cell circuit from extreme conditions. The junction box is also injected with special silicon, guaranteeing no water ingress.
Cells protected from hot spots
Where used on a camper van or boat, partial shading of a solar panel is typical. In these circumstances, heat build-up and damaging hot spots can occur leading to a significantly reduced life cycle of the panel. The larger 60w and above PV Logic flexi panels have up to two shading diodes housed within the fully waterproof junction box to prevent this occurrence.
There are no square edges on a PV Logic semi-flexible solar panel! Rounded panel corners and a unique curved junction box provide superior adhesion, no snag lamination and no sharp edges. The junction box is mechanically fixed in addition to being bonded to the panel. Strain relief is provided for the fitted 4m UV stabilised PV cable ensuring it cannot be accidentally pulled from the junction box.
Underside cable exit (100w and 150w panels only)
The cable of the 100w and 150w flexi panels exits the panel from the underside allowing for a completely flush fit to your roof or decking. A remote shading diode box is ensures consistent performance even in partially shady conditions. The 100w and 150w panels are available with a white back sheet or all black.
The semi-flexible range can be bonded to flat or slight curved surfaces (3cm curve per metre) such as painted aluminium, metal, GRP and fibreglass using Simson ISR 70-03. The aluminium layer is also pre-drilled with 4.5mm holes should the panel need to be mechanically fixed as well as or instead of bonding. For more information about what sets the PV Logic Flexi range apart from other panels click here.
Please only use the glue pattern below (this is covered in more detail in the instructions), which ensures air flow under the panel is achieved preventing heat build-up and potential warping under extreme heat.
Complete your kit with fixing accessories
Depending on the shape and size of your roof, there are various options for attaching the panel. We can supply you with your combination choice of gland, bonding agent and/or 3M tape. Buy PV Logic stands, brackets and fixings here
High efficiency crystalline cell for “all weather” charging
Water resistant, robust construction for outdoor use.
In built diode protects against battery discharge
20 year cell performance warranty**
Salt spray tested
Tough and robust
UV light tested
2 year product warranty
Weight (Kg) 5.6
*Watts per day (W) 720
*Amp hours per day (A) 40.92
nominal voltage17.6Imp (A)
nominal current 6.82Voc (V) 21.9Isc (A)
short circuit current 7.36
IP (Ingress Protection) Rating IP69
*Watts and Amp hours/day based on six hours of average daily peak sunshine hours. Above specification at standard test conditions (STC) 1000w/m2, Cell Temp 25c